| |
| 1.03 Material Storage & Handling |
|
A. |
Store all materials in their original
unopened containers, with labels intact. Follow manufacturer's instructions for storage
and handling. |
|
B. |
Carefully handle roll goods. |
|
C. |
Store all materials in a dry area protected from exposure
to water & direct sunlight. |
|
|
|
| 1.04 Site Conditions |
|
A. |
Roof surface must be free of ponding water, ice or snow.
Roof surface should be designed to be water free no longer than 48 hours after
precipitation. |
|
B. |
Do not install during inclement weather. |
|
|
|
| 1.05 Quality Assurance |
|
A. |
Contractor shall be approved and licensed, in writing, by
International Diamond Systems. |
|
|
|
| 1.06 Warranty |
|
A. |
International Diamond Systems will provide a 5, 10 or 15
year warranty commencing at the date of final inspection & approval by the
International. Contact International
Diamond Systems for further information on warranty. |
|
|
|
| Part 2. Products |
| 2.01 Product Statement |
|
A. |
All products used to install International Diamond Systems
must be products of International Diamond Systems or approved by International Diamond
Systems. |
|
|
|
| 2.02 Membrane |
|
A. |
International Diamond Systems EPDM (Ethylene, Propylene,
Diene, Terpolymer). Available in widths from 7 to 50 feet and lengths of 50 to 100
feet. Available in .045 and .060, Black. (note: for further technical data see table.) |
|
|
|
| 2.03 Insulation |
|
A. |
A minimum 1/2" of approved insulation must be used
over the existing roof or deck. |
|
B. |
Insulation must be of proper density and thickness to
support traffic and meet building code requirements. |
|
C. |
Contact International Diamond Systems
for a complete list of approved insulation. |
|
|
|
| 2.04 System Components |
|
A. |
Flashings: Uncured EPDM |
|
B. |
Pre-Fabricated Pipe Boots |
|
C. |
Seam Tape - 4" Cured Butyl |
|
D. |
Bonding Adhesive RTS 010 |
|
E. |
Splice Adhesive RTR 019 |
|
F. |
Activator |
|
G. |
Lap Sealant LS014 |
|
H. |
Water Cut-Off WS024 |
|
I. |
Pourable Sealer PS018 |
|
J. |
Night Stop |
|
K. |
Termination Bar |
|
L. |
Batten Bar |
|
M. |
Diamond 105 Plate - 7" x 7" Self-Adhering Plate |
|
N. |
I-90 Disc - 4" diameter 16 gauge steel disc |
|
O. |
Cover Tape - 7" Seam Tape/EPDM Laminate |
|
P. |
Roof Walkway Pads - 8mm x 30" x30'(ft.) |
|
Q. |
Bonding Plates - 8" High Impact Polystrene |
|
R. |
Fasteners: Corrosion resistant. Proper type, length,
size, and strength required. |
|
|
|
| 2.05 Related Products By Others |
|
A. |
Vapor Barriers |
|
B. |
Wood Nailers |
|
C. |
Splash Blocks |
|
D. |
Thermal Barrier |
|
|
|
| Part 3. Execution |
| 3.01 Inspection & Preparation |
|
A. |
Consult International Diamond Systems specification manual
for instructions, inspection, and preparation of substrate. |
|
B. |
Substrate must be dry, clean and smooth, free of
protrusions, sharp edges, loose and foreign material. |
|
|
|
| 3.02 Insulation |
|
A. |
Loosely lay insulation and attach in accordance with
manufacturer's requirements. Cut insulation around penetrations. |
|
B. |
Install only as much insulation as can be covered by
membrane the same day. |
|
|
|
| 3.03 Installation Instructions |
|
A. |
See appropriate system for description |
|
|
- Diamond 105
- Seal-A-Plate
- Fully Adhered
- Ballasted |
|
|
|
| 3.04 Cleaning |
|
A. |
Remove construction trash and debris from roof
at end of each work day. |
|
|
|
| 3.05 Field Service |
|
A. |
An International Diamond Systems Field
Technician will inspect the installation for approval of warranty upon completion of the
system application. |
|
|
|
back
to top |
